1 /* Definitions for DigiBoard ditty(1) command. */
2
3 #if !defined(TIOCMODG)
4 #define TIOCMODG (('d'<<8) | 250) /* get modem ctrl state */
5 #define TIOCMODS (('d'<<8) | 251) /* set modem ctrl state */
6 #endif
7
8 #if !defined(TIOCMSET)
9 #define TIOCMSET (('d'<<8) | 252) /* set modem ctrl state */
10 #define TIOCMGET (('d'<<8) | 253) /* set modem ctrl state */
11 #endif
12
13 #if !defined(TIOCMBIC)
14 #define TIOCMBIC (('d'<<8) | 254) /* set modem ctrl state */
15 #define TIOCMBIS (('d'<<8) | 255) /* set modem ctrl state */
16 #endif
17
18 #if !defined(TIOCSDTR)
19 #define TIOCSDTR (('e'<<8) | 0) /* set DTR */
20 #define TIOCCDTR (('e'<<8) | 1) /* clear DTR */
21 #endif
22
23 /************************************************************************
24 * Ioctl command arguments for DIGI parameters.
25 ************************************************************************/
26 #define DIGI_GETA (('e'<<8) | 94) /* Read params */
27
28 #define DIGI_SETA (('e'<<8) | 95) /* Set params */
29 #define DIGI_SETAW (('e'<<8) | 96) /* Drain & set params */
30 #define DIGI_SETAF (('e'<<8) | 97) /* Drain, flush & set params */
31
32 #define DIGI_GETFLOW (('e'<<8) | 99) /* Get startc/stopc flow */
33 /* control characters */
34 #define DIGI_SETFLOW (('e'<<8) | 100) /* Set startc/stopc flow */
35 /* control characters */
36 #define DIGI_GETAFLOW (('e'<<8) | 101) /* Get Aux. startc/stopc */
37 /* flow control chars */
38 #define DIGI_SETAFLOW (('e'<<8) | 102) /* Set Aux. startc/stopc */
39 /* flow control chars */
40
41 #define DIGI_GETINFO (('e'<<8) | 103) /* Fill in digi_info */
42 #define DIGI_POLLER (('e'<<8) | 104) /* Turn on/off poller */
43 #define DIGI_INIT (('e'<<8) | 105) /* Allow things to run. */
44
45 struct digiflow_struct
46 {
47 unsigned char startc; /* flow cntl start char */
48 unsigned char stopc; /* flow cntl stop char */
49 };
50
51 typedef struct digiflow_struct digiflow_t;
52
53
54 /************************************************************************
55 * Values for digi_flags
56 ************************************************************************/
57 #define DIGI_IXON 0x0001 /* Handle IXON in the FEP */
58 #define DIGI_FAST 0x0002 /* Fast baud rates */
59 #define RTSPACE 0x0004 /* RTS input flow control */
60 #define CTSPACE 0x0008 /* CTS output flow control */
61 #define DSRPACE 0x0010 /* DSR output flow control */
62 #define DCDPACE 0x0020 /* DCD output flow control */
63 #define DTRPACE 0x0040 /* DTR input flow control */
64 #define DIGI_FORCEDCD 0x0100 /* Force carrier */
65 #define DIGI_ALTPIN 0x0200 /* Alternate RJ-45 pin config */
66 #define DIGI_AIXON 0x0400 /* Aux flow control in fep */
67
68
69 /************************************************************************
70 * Values for digiDload
71 ************************************************************************/
72 #define NORMAL 0
73 #define PCI_CTL 1
74
75 #define SIZE8 0
76 #define SIZE16 1
77 #define SIZE32 2
78
79 /************************************************************************
80 * Structure used with ioctl commands for DIGI parameters.
81 ************************************************************************/
82 struct digi_struct
83 {
84 unsigned short digi_flags; /* Flags (see above) */
85 };
86
87 typedef struct digi_struct digi_t;
88
89 struct digi_info
90 {
91 unsigned long board; /* Which board is this ? */
92 unsigned char status; /* Alive or dead */
93 unsigned char type; /* see epca.h */
94 unsigned char subtype; /* For future XEM, XR, etc ... */
95 unsigned short numports; /* Number of ports configured */
96 unsigned char *port; /* I/O Address */
97 unsigned char *membase; /* DPR Address */
98 unsigned char *version; /* For future ... */
99 unsigned short windowData; /* For future ... */
100 } ;
101
This page was automatically generated by the
LXR engine.
Visit the LXR main site for more
information.