~ [ source navigation ] ~ [ diff markup ] ~ [ identifier search ] ~ [ freetext search ] ~ [ file search ] ~

Linux Cross Reference
Linux-2.6.17/Documentation/networking/dmfe.txt

Version: ~ [ 2.6.16 ] ~ [ 2.6.17 ] ~
Architecture: ~ [ ia64 ] ~ [ i386 ] ~ [ arm ] ~ [ ppc ] ~ [ sparc64 ] ~

  1 Davicom DM9102(A)/DM9132/DM9801 fast ethernet driver for Linux.
  2 
  3 This program is free software; you can redistribute it and/or
  4 modify it under the terms of the GNU General   Public License
  5 as published by the Free Software Foundation; either version 2
  6 of the License, or (at your option) any later version.
  7 
  8 This program is distributed in the hope that it will be useful,
  9 but WITHOUT ANY WARRANTY; without even the implied warranty of
 10 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 11 GNU General Public License for more details.
 12 
 13 
 14 This driver provides kernel support for Davicom DM9102(A)/DM9132/DM9801 ethernet cards ( CNET
 15 10/100 ethernet cards uses Davicom chipset too, so this driver supports CNET cards too ).If you
 16 didn't compile this driver as a module, it will automatically load itself on boot and print a
 17 line similar to :
 18 
 19         dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
 20 
 21 If you compiled this driver as a module, you have to load it on boot.You can load it with command :
 22 
 23         insmod dmfe
 24 
 25 This way it will autodetect the device mode.This is the suggested way to load the module.Or you can pass
 26 a mode= setting to module while loading, like :
 27 
 28         insmod dmfe mode=0 # Force 10M Half Duplex
 29         insmod dmfe mode=1 # Force 100M Half Duplex
 30         insmod dmfe mode=4 # Force 10M Full Duplex
 31         insmod dmfe mode=5 # Force 100M Full Duplex
 32 
 33 Next you should configure your network interface with a command similar to :
 34 
 35         ifconfig eth0 172.22.3.18
 36                       ^^^^^^^^^^^
 37                      Your IP Adress
 38 
 39 Then you may have to modify the default routing table with command :
 40 
 41         route add default eth0
 42 
 43 
 44 Now your ethernet card should be up and running.
 45 
 46 
 47 TODO:
 48 
 49 Implement pci_driver::suspend() and pci_driver::resume() power management methods.
 50 Check on 64 bit boxes.
 51 Check and fix on big endian boxes.
 52 Test and make sure PCI latency is now correct for all cases.
 53 
 54 
 55 Authors:
 56 
 57 Sten Wang <sten_wang@davicom.com.tw >   : Original Author
 58 Tobias Ringstrom <tori@unhappy.mine.nu> : Current Maintainer
 59 
 60 Contributors:
 61 
 62 Marcelo Tosatti <marcelo@conectiva.com.br>
 63 Alan Cox <alan@redhat.com>
 64 Jeff Garzik <jgarzik@pobox.com>
 65 Vojtech Pavlik <vojtech@suse.cz>

~ [ source navigation ] ~ [ diff markup ] ~ [ identifier search ] ~ [ freetext search ] ~ [ file search ] ~

This page was automatically generated by the LXR engine.
Visit the LXR main site for more information.